Brix Setup
IDC Pro Installation Genie — Begin Your Installation
-
Access Brix Setup
Once the syrup lines are purged, it is now time to set the ratios. You MUST have ice on the cold plate for at least 30 minutes prior to setting the ratio. If you have not done so already, add ice to the hopper.
Note: There is no syrup separator needed, you will use the service UI to set the water flow rate and the syrup flow rate separately.
-
Valve Layout Description
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Note: The valve layout on the screen matches the physical valve layout in the IDC Pro
Example: A1 is the 1st valve from left on the top row
Example: CW1 is the 6th valve from left on the top row
Total Water Flow does not affect actual water flow rate, this is to capture sales data. Do not adjust!
-
Setting Left Side Water Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Left Side Flowrate Target:
CW1 = 7oz.
CW2 = 3oz.
PW1 = 7oz.
PW2 = 3oz.
Carb Water = 10oz.
Plain Water = 10oz.Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining water valves, you MUST set flow rate for all water.
Tap carb water to check total CW flow rate, it will activate CW1 and CW2 – adjust CW 1 as needed to achieve 10oz.
Tap plain water to check total PW flow rate, it will activate PW1 and PW2 – adjust PW 1 as needed to achieve 10oz.
Note: You do not need to check water every time you check your syrup.
-
Setting Right Side Water Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Right Side Flowrate Target:
CW3 = 7oz.
CW4 = 3oz.
PW3 = 7oz.
PW4 = 3oz.
Carb Water = 10oz.
Plain Water = 10oz.Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining water valves, you MUST set flow rate for all water.
Tap carb water to check total CW flow rate, it will activate CW3 and CW4 – adjust CW 3 as needed to achieve 10oz.
Tap plain water to check total PW flow rate, it will activate PW3 and PW4 – adjust PW 3 as needed to achieve 10oz.
Note: You do not need to check water every time you check your syrup.
-
Setting Left Side Syrup Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Left Side Flowrate Target: Follow syrup manufacturer or account specs
Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining syrup valves.
For accurate measurements, it is advised to flush the syrup chamber of the brix cup after each dispense.
Note: You do not need to check water every time you check your syrup.
-
Setting Right Side Syrup Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Right Side Flowrate Target: Follow syrup manufacturer or account specs
Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining syrup valves.
For accurate measurements, it is advised to flush the syrup chamber of the brix cup after each dispense.
Note: You do not need to check water every time you check your syrup.
-
Setting Left Side Flavor Shot Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Left Side Flowrate Target: Follow syrup manufacturer or account specs
Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining syrup valves.
For accurate measurements, it is advised to flush the syrup chamber of the brix cup after each dispense.
Note: You do not need to check water every time you check your syrup.
-
Setting Right Side Flavor Shot Flowrate
When you activate a valve in Brix Setup, it will dispense for a pre-programmed 4 second dispense.
Right Side Flowrate Target: Follow syrup manufacturer or account specs
Place your brix cup under the appropriate nozzle.
Tap the appropriate valve to activate the dispense and capture the volume.
Adjust the flow control as needed to achieve the correct flow rate; rotate clockwise for more flow and counterclockwise for less flow. Repeat for remaining syrup valves.
For accurate measurements, it is advised to flush the syrup chamber of the brix cup after each dispense.
Note: You do not need to check water every time you check your syrup.